Installing Commercial Window Films Since 1985

Solar Window Film Performance Ratings Explained: SHGC, TSER, VLT and More

Get a Quote

Complete the form and we’ll be in touch.

Two solar window films may both be described as effective heat-control products while allowing very different amounts of daylight into a building. Their specification sheets can explain that difference, but only when the ratings are considered together and the test conditions are understood. A high percentage beside “solar rejection” or “infrared rejection” is not, by itself, enough to establish how a film will perform on a particular commercial window.

How Performance Ratings Fit Into Solar Film Selection

For building owners, facility managers, architects and project teams evaluating commercial solar window film, the most useful questions are practical: How much solar heat may enter through the glazing? What happens to daylight and glare? Will the film affect the appearance of the glass, and do the published figures apply to the building’s existing windows? Understanding the principal solar window film performance ratings makes those questions easier to address before product selection.

Our solar control window film overview explains why commercial facilities install solar film — to reduce solar heat gain, minimize glare while keeping natural light, and block ultraviolet exposure — and notes that performance levels vary depending on film selection, glazing type and building orientation. Its FAQs introduce two of the measures used to describe that performance: the Solar Heat Gain Coefficient, rated from 0 to 1, and the Shading Coefficient. This guide continues from there, explaining what each commonly published rating describes, how the ratings relate to one another and how to check whether a specification sheet applies to the windows being evaluated.

Why Solar Window Film Ratings Need Context

Solar-control films manage the way sunlight interacts with glass. Depending on the product and glazing, incoming solar energy may be transmitted, reflected or absorbed. Some absorbed energy is subsequently released toward the interior and some toward the exterior. That is why the amount of sunlight a film appears to block is not necessarily the same as the reduction in solar heat entering the occupied space.

The published numbers generally describe a particular film-and-glass combination under specified calculation or measurement conditions. They are useful for comparing products, but they do not directly predict a room’s temperature, annual utility savings or the experience of occupants at every time of day. Window orientation, building location, shading, existing glazing, internal heat loads and HVAC operation all influence the outcome.

It is also important to keep the ratings’ purpose clear. Solar-control values describe optical and thermal behavior; they do not establish resistance to forced entry, blast loads or glass-fragment hazards. Those concerns require different evidence, as explained in CWS’s resource on security window film testing standards. A product with strong solar performance should never be assumed to meet a security requirement solely because of its solar ratings.

Understanding Solar Heat Ratings: SHGC, TSER and IR Rejection

Four terms frequently appear in solar control window film ratings. They are related, but they are not interchangeable. Two assess overall solar heat gain, one is an older comparative measure, and one may describe only a selected portion of the solar spectrum.

Where incident solar energy goes at a filmed windowSunlight striking glass with solar film is partly reflected back outside, partly transmitted into the building, and partly absorbed by the glass and film. Some absorbed energy is released back toward the exterior and some flows inward. The transmitted portion plus the inward-flowing absorbed portion make up the solar heat gain described by SHGC. TSER is the remainder: total solar energy rejection equals one minus SHGC, times 100 percent. In the illustrative example, an SHGC of 0.35 corresponds to a TSER of 65 percent.EXTERIORINTERIORGlass + filmIncident solar energy(UV, visible and infrared)Reflectedback outsideAbsorbed, released outwardTransmittedAbsorbed, then flows inwardSolar heat gain= SHGC (0 to 1)lower = less heat inTSER = (1 − SHGC) × 100%Illustrative example: SHGC 0.35 corresponds to TSER 65% (same glass and rating conditions)Not to scale; proportions vary by film and glass.

Solar Heat Gain Coefficient (SHGC)

Solar Heat Gain Coefficient, or SHGC, expresses the fraction of incident solar energy that enters through a glazing system. It includes sunlight transmitted directly through the glass and the inward-flowing portion of energy absorbed by the glazing. SHGC is expressed as a value from 0 to 1; a lower number indicates less solar heat gain under the stated rating conditions.

For example, an SHGC of 0.35 means that the rated glazing configuration admits 35% of the incident solar energy as heat under the calculation conditions. It does not mean the building’s cooling costs will fall by 35%, because solar gain through one part of the building envelope is only one contributor to the overall heating and cooling load. When comparing films, check that both SHGC values refer to equivalent glass assemblies.

Total Solar Energy Rejection (TSER)

Total Solar Energy Rejection, or TSER, expresses the share of total incident solar energy not admitted as heat through the rated glazing configuration. It is commonly presented as a percentage, with a higher value indicating greater rejection. When the two values use the same assumptions and glazing basis, TSER = (1 − SHGC) × 100%. Thus, an illustrative SHGC of 0.35 corresponds to 65% TSER for that same configuration.

TSER is often easier to interpret in a product comparison because it states a rejection percentage. Still, a “65% TSER” figure measured or calculated for one reference glass cannot automatically be applied to a different insulated, coated or tinted window. The existing glazing matters, and the film should be evaluated as part of that assembly.

Shading Coefficient (SC)

Shading Coefficient is an older measure that compares solar heat gain through a glazing configuration with the heat gain through a specified clear-glass reference under the same conditions. Like SHGC, a lower value generally indicates less solar heat gain. It still appears on some architectural film specification sheets, but the reference-based nature of SC makes it important to identify the basis of comparison rather than treating the number as a standalone percentage.

Infrared Rejection (IRR)

Infrared rejection describes how a film treats infrared radiation, but the figure can be misleading if the tested wavelength range is not disclosed. One manufacturer may report rejection across a broad near-infrared range; another may highlight performance at a narrow band of wavelengths. Neither number represents the complete solar spectrum, which also includes visible and ultraviolet radiation.

A prominent claim such as “high infrared rejection” may be technically valid for its stated test band without indicating equally high total solar energy rejection. For building-level solar heat comparisons, SHGC or TSER on a common glazing basis usually provides a more complete starting point. IRR is useful supporting information once its measurement method and wavelength range are known.

Reading Visible Light, Glare and Reflectance Ratings

Reducing solar heat does not always require making a window substantially darker. Commercial film products can differ significantly in the relationship between heat control and daylight, so the optical ratings deserve as much attention as the solar-energy figures.

Visible Light Transmission (VLT), also called visible transmittance (VT), is the proportion of visible light passing through the rated glass-and-film configuration. Higher VLT generally means more daylight reaches the interior; lower VLT means less. A lower-transmission film may help reduce uncomfortable brightness, but the trade-off could be a darker interior or greater reliance on electric lighting. Conversely, some spectrally selective films are designed to maintain relatively high visible-light transmission while reducing solar heat gain.

CWS installs solar control film at Kreeger Museum, Washington, D.C.
At The Kreeger Museum in Washington, D.C., CWS replaced older solar film with a spectrally selective solar control film that admits daylight while blocking UV rays and reducing solar heat gain.

Glare reduction is often shown as a percentage relative to an unfilmed reference. It can help compare options, but it is not a direct measure of visual comfort at a workstation. Sun angle, reflected light, screen placement, window size and the direction occupants face all affect glare. If the project involves offices, control rooms or other screen-intensive spaces, samples should be assessed under representative lighting conditions rather than selected by the glare percentage alone.

Visible Light Reflectance (VLR) indicates the share of visible light reflected by the glazing. Some specification sheets report separate interior and exterior reflectance figures because the two appearances can differ. These values matter for façade consistency, the appearance of the building from the street and reflections seen by occupants. A film with strong heat rejection is not necessarily highly reflective, and a reflective-looking film is not automatically the best solution for every commercial property.

What U-Factor, Emissivity and UV Rejection Tell Us

Solar heat gain is only one component of window performance. Another is heat transfer caused by the temperature difference between indoor and outdoor conditions. U-factor (also called U-value) measures that transfer; a lower U-factor indicates better resistance to heat flow under the relevant conditions. Unlike SHGC, which concerns solar radiation, U-factor is concerned with heat transfer associated with a temperature difference.

Low-emissivity (Low-E) technology can reduce long-wave radiant heat transfer at the glass surface, potentially improving the insulating behavior of a compatible glazing assembly. However, a solar-control film should not be assumed to lower U-factor simply because it rejects sunlight. Any claimed winter heat-loss benefit needs to be supported by the specific film-and-glass rating, with the existing glazing construction and coating surfaces taken into account.

Ultraviolet (UV) rejection describes the portion of UV radiation blocked over the measurement range stated by the manufacturer. Many architectural films have high published UV-rejection values, which can be valuable in commercial interiors containing merchandise, furnishings, artwork or exhibits. Even so, UV protection is not a guarantee against fading or deterioration. Visible light, exposure duration, temperature, humidity and the sensitivity of individual materials also contribute to damage. For sensitive collections in museums and galleries, film performance should be assessed as one element of a wider light and environmental-control approach.

How to Compare Solar Window Film Specification Sheets

The most reliable comparison begins by confirming that the published figures describe equivalent conditions. A film that appears to outperform another on a brochure may have been rated on different glass, against a different reference or using a different method. The following table summarizes the principal metrics and the question each one should answer.

RatingWhat it describesWhat to check when comparing products
SHGCFraction of total incident solar energy entering as heatLower usually means less solar gain; verify the glass configuration.
TSERPercentage of total solar energy rejectedHigher means more rejection; compare on the same glazing basis.
VLT / VTProportion of visible daylight transmittedCheck the daylight-versus-glare trade-off, not just the highest or lowest number.
Visible reflectanceVisible light reflected inward and outwardReview separate interior/exterior values and façade appearance.
IR rejectionRejection within a stated infrared wavelength rangeConfirm the wavelength band; do not substitute IRR for TSER.
U-factorHeat transfer due to indoor/outdoor temperature differenceVerify units and whether the result is for the same glazing assembly.
UV rejectionUV radiation blocked within a specified test rangeCheck the definition and avoid interpreting it as complete fade prevention.
Which part of sunlight each solar film rating describesThe solar spectrum divided into ultraviolet (about 300 to 380 nanometers), visible light (about 380 to 780 nanometers) and near-infrared (about 780 to 2,500 nanometers). UV rejection describes the ultraviolet band. VLT, visible reflectance and glare reduction describe the visible band. Infrared rejection describes only the infrared band its manufacturer states, which may be narrow or broad. SHGC and TSER account for solar heat from the whole spectrum. U-factor is different: it describes heat transfer driven by the indoor and outdoor temperature difference, not incoming sunlight.THE SOLAR SPECTRUM (NOT TO SCALE)UltravioletVisible lightNear-infrared~300–380 nm~380–780 nm~780–2,500 nmUV rejectionVLT, visiblereflectance, glareIR rejectionor a broader bandOnly the band the manufacturer statesSHGC / TSERSolar heat admitted from the whole spectrumU-factorNot a slice of sunlight: heat flow driven by the indoor–outdoor temperature difference.

Start with the glass used for the published ratings

Look for a statement such as “applied to 1/4-inch clear glass” or an equivalent glazing description. That line is fundamental, not fine print. As one real-world example of reporting practice, 3M’s published architectural-film property summary provides separate tables for clear, tinted and other glazing conditions. The same film can show different combined-system values when the glass changes. A value reported for single-pane clear glass should therefore not be used as an exact prediction for a double-pane, Low-E or otherwise treated window.

Where available, compare the existing glass without film and the proposed glass with film. That gives the project team a more meaningful understanding of the proposed change than a single film label. It can also reveal when a promising solar rating comes with a substantial reduction in daylight or an appearance change that matters to the building.

Distinguish certified results from manufacturer-reported data

The National Fenestration Rating Council (NFRC) administers a window-film rating and certification program, and its product directory can be used to check applicable certified listings. An NFRC-certified rating is not the same thing as a product brochure saying that its values were calculated using a referenced test procedure. Both kinds of information can be useful, but they should be described accurately.

In particular, not every number printed on a technical data sheet is necessarily an NFRC-certified metric. Manufacturers may separately report UV blocking, infrared rejection, glare reduction or other characteristics. Ask which values are independently certified, which are manufacturer-reported and which glazing or test conditions support each figure. When the film is being specified for a particular building, obtain documentation applicable to that project rather than relying exclusively on a general marketing comparison.

Look for the heat-and-daylight balance

Two films with similar TSER may produce different daylight levels and visible reflectance, leading to very different occupant experiences. A useful supplementary measure is the light-to-solar-gain ratio (LSG), calculated by dividing visible transmittance (expressed as a decimal) by SHGC. A higher LSG generally indicates more daylight transmitted relative to solar heat gain, although it does not replace the underlying ratings or determine whether a product is suitable for a specific space.

Selection also requires a separate glass-compatibility review. Film type, glazing construction, existing coatings, glass thickness, pane dimensions, thermal-stress considerations and the intended interior or exterior installation position can affect suitability. Performance figures alone do not establish that a particular film is appropriate for every existing window.

Which Ratings Matter Most for Different Commercial Building Goals?

There is no single rating that identifies the best solar film for every commercial building. The right emphasis depends on the problem the owner is trying to solve and the compromises that the occupied space can accept.

  • Reducing solar heat gain: Begin with SHGC or TSER for the relevant glazing assembly, then consider window orientation, exposure and the amount of glazing. A strong laboratory rating supports product comparison but is not a building-specific savings forecast.
  • Preserving daylight in offices: Compare VLT alongside SHGC and, where useful, LSG. Spectrally selective options may offer a better daylight-to-heat balance than a darker film, but interior and exterior reflectance still need review.
  • Managing glare at workstations: Evaluate VLT and the basis of any glare-reduction rating, then assess actual sightlines, screen locations and periods of direct sun. A single percentage cannot describe every occupant’s visual experience.
  • Protecting displayed materials: Review the stated UV-rejection range while considering visible-light exposure and the sensitivity of the materials. For valuable collections, conservation requirements must guide the decision.
  • Addressing winter heat loss: Ask whether the specific film has documented Low-E or U-factor performance on the applicable glazing. Solar rejection alone is not evidence of improved insulation.

These priorities can coexist across a single property, particularly where façade orientation and interior use vary. For example, a heavily glazed office elevation may call for a different daylight and glare balance from a lobby or exhibit area. Large commercial installations can also involve different glazing types within the same project. CWS’s Techworld solar film project illustrates the scale at which these distinctions can become relevant: the project included solar-control film on more than a thousand panes, alongside a separate solar-security film scope.

A Practical Checklist Before Accepting Solar Film Ratings

Before using a specification sheet to shortlist products for a commercial building, confirm the following with the manufacturer or installation team:

  • Product identity: Is the exact film series, product and intended interior or exterior application identified?
  • Reference glazing: What glass type, thickness and construction were used to produce the published figures?
  • Comparable basis: Do SHGC, TSER, VLT and reflectance values refer to the same film-and-glass assembly and rating conditions?
  • Documented source: Which metrics are NFRC-certified, which follow a recognized method, and which are manufacturer-reported?
  • Infrared and UV definitions: What wavelength ranges and test conditions support the advertised rejection percentages?
  • Visual impact: What will the selected VLT and interior/exterior reflectance mean for daylight, glare and exterior appearance?
  • Glass suitability: Has the proposed film been reviewed for the actual glazing, coatings, dimensions, installation position and relevant thermal-stress risks?
  • Project outcome: Are anticipated comfort or energy benefits being evaluated against the building's actual exposures and operating conditions rather than presented as guaranteed results?

A defensible specification is one in which the product data, existing glazing and intended building outcomes have been considered together. These questions also help explain why two products that look similar on a marketing sheet may be appropriate for different spaces.

Putting the Ratings to Work

Solar window film ratings are most useful when they are read as a set of related measurements. SHGC and TSER explain solar heat gain; VLT, glare and reflectance describe the visible-light trade-offs; and U-factor and UV rejection address different aspects of performance. The deciding step is to confirm how those values were obtained and whether they apply to the glazing being evaluated. This provides a stronger basis for commercial product selection than any single headline percentage.

Discussing Solar Film Performance for Your Building

For a commercial property, the next step is to review the building’s existing glazing and priorities alongside the relevant product data. As our solar control window film installation page notes, each project is evaluated individually so that the selected film system aligns with the building’s characteristics, operational needs and energy performance goals. Contact Commercial Window Shield to discuss the project scope and the performance characteristics that matter most to the application.

Technical Note

This article explains commonly published solar window film ratings for general educational purposes. Reported values depend on the identified film, glass construction, measurement or calculation procedure, and rating conditions. They are not a substitute for product-specific documentation, glass-compatibility review or a building-level performance assessment. Any projected comfort, energy or conservation outcome should be evaluated for the particular project.

References and Technical Sources

The information presented in this article draws on published glazing industry guidance and technical documentation, including:

What Our Customers Say

Donald White, Superintendent
U.S. Capitol
“The only thing I’ve seen that rivals a project coordination of this magnitude is a presidential inauguration.”
Joe Neid, Project Engineer
FBI Headquarters
"Commercial Window Shield successfully completed the work on time."
Chris Jasiota, Project Executive
DAVIS Construction
“Truly, it is great to have a go-to partner in the film world.”
Stephen Saieed, Owner
Masonboro Construction
“We originally subcontracted the security film installation work to another company, which backed out on us eight days before our deadline. Commercial Window Shield stepped in and completed the project in three days. The installation was meticulous.”
Cathy Boles, Development Director
Washington Convention and Sports Authority
“Thank you for meeting our ridiculous time frame for the installation of the blackout window film at the Washington Convention Center.”
William C. Salee, Project Manager
Rockwall [Texas] Independent School District
“The Installation Team Performed Above Our High Level Of Expectation. They Worked Very Efficiently And Completed The Project In Less Time Than Had Been Anticipated.”
Alan Haskel, Director, Administration
Public Broadcasting Service
“The film Commercial Window Shield installed looks really good. Your team did a really nice job. Thanks for the good work.”
Phil Blum, Castle Construction
United Airlines Terminal, O'Hare International Airport
“Not only was the work completed and done well, it was completed nearly six months ahead of schedule.”
Tom Conkling, Building Manager
Merrill Lynch headquarters, NYC
“Impressive work!”
Matt Pope, Project Executive
HITT Construction
“Commercial Window Shield has been installing all types of window film for us for over 10 years. They do a great job and are very responsive and helpful.”
Tony Suszczynski, Emergency Preparedness Coordinator
USF/Shands [Fla.] Medical Center
“Your crew works as a well-oiled machine. They take their craft to the next level. Let’s just say they are the best.”
Charles M. Clancy
Pentagon Force Protection Agency
“You guys really came through when it was needed. Your quick response and professionalism were very much appreciated.”
Madico Window Film Dealer of the Year award badge

Need A Quote?

Get a Quote

Complete the form and we’ll be in touch.